EF70-300mm f/4.5-5.6 DO IS USM
ENG
Instruction
a Safety Precautions
T
his device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to part 15 of the FCC Rules.
These lims are designed to provide reasonable protection against
harmful rference in a residential installation. This equipment
ates, ses and can radiate radio frequency energy and, if not
led and used in accordance with the instructions, may cause
hmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
a Safety Precautions
• Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
• Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a
fire.
Handling Cautions
• If the lens is taken from a cold environment in
a warm one, condensation may develop on the
lens surface and internal parts. To preven
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
• Increase the separation between the equipment and receiver.
•
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
a Shooting Precautions
If a very bright spotlight like a mercury lamp is
photographed in a dark place with this lens, a halo
of light may occasionally appear around the light
source because of the DO elements.
ENG-2
Nomenclature
Focus mode switch (→ 4)
Hood mount (→ 5)
Distance scale (→ 10)
Zoom ring (→ 5)
Lens mount index (→ 4)
Filter mounting
thread (→ 11)
Focusing ring (→ 4)
Image stabilizer switch (→ 7)
Image stabilizer
mode selector switch (→ 7)
Contacts (→ 4)
Zoom ring lock lever (→ 6)
For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-3
1. Mounting and
2. Setting the Focus
Mode
Detaching the Lens
See your camera’s instructions for details on
mounting and detaching the lens.
hoot in autofocus (AF) mode, set the focus
mde switch to AF.
To use only manual focusing (MF), set the focus
mode switch to MF, and focus by turning the
focusing ring. The focusing ring always works,
regardless of the focus mode.
• After detaching the lens, place the lens with t
rear end up to prevent the lens surface and
electrical contacts from getting scratchd.
• If the contacts get soiled, scratched, or ave
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
• If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
• If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
index and the
K
index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
ENG-4
3. Zooming
4. Hood
To zoom, turn the zoom ring.
The ET65B hood can keep unwanted light out of
thlenand also protects the front of the lens
rainsnow, and dust.
Aach and align the hood to the hood mount on
he front of the lens, and turn the hood as shown
by the arrow to secure it.
Be sure to finish zooming before focusing.
Zooming after focusing can affect the focus.
The hood can be reverse-mounted on the lens
for storage.
• Part of the picture may be blocked if the hood is
not attached properly.
• When attaching or detaching the hood, grasp
the base of the hood to turn it. To prevent
deformation, do not grasp the rim of the hood to
turn it.
ENG-5
5. Fixing the Zoom Ring
The zoom ring can be fixed to keep the lens at the shortest point. This function is convenient for
carrying a camera on a strap because it prevents the lens from extending.
Turn the m ng to the
widest pn (70mm).
Slide the zoom ring lock
lever in the direction
indicated by the arrow.
• To release the zoom ring, slide
the zoom ring lock lever in the
direction opposite to the arrow.
The zoom ring can only be locked at maximum wide angle.
ENG-6
6. Image Stabilizer Settings
You can use the image stabilizer in AF or MF mode.
Set the STABILIZER switch
to
Select the staer mde.
When you press the shutter
button halfway, the Image
Stabilizer will start
.
• MODE recs vibrations
in all dir. It is mainly
ffective foshooting still
subjecs.
• MODE 2: It compensates for
vertical camera shake during
following shots in a horizontal
direction, and compensates for
horizontal camera shake
during following shots in a
vertical direction.
• If you are not going to use the
image stabilizer function, set
operating.
the switch to
.
• Make sure the image in the
viewfinder is stable, then press
the shutter button the rest of
the way down to take the
picture.
ENG-7
7. Tips on Using the Image Stabilizer
The image stabilizer in this lens is effective for hand-held shots under the following conditions.
● MODE 1
● MODE 2
• In semi-darkened areas such as indoors or
outdoors at night.
• When panning subjects in motion.
• In locations where flash photography is
prohibited, such as art museums and theater
stages.
• In situations where your footing is uncertain.
• In situations where fast shutter settings cannot
be used.
ENG-8
Tips on Using the Image Stabilizer
• The Image Stabilizer cannot compensate for a
blurred shot caused by a subject that moved.
• When you use a tripod, the Image Stabilizer
should be turned off to save battery power.
• The stabilizer is equally effective for hand-held
photography and photography with a monopod.
• The image stabilizer function also operates
when the lens is used with an Extension Tube
EF12 ll or EF25 ll.
• Pictures may look distorted after being taken
dpending on the camera, but this doesn't affect
oting.
•
Set the STABILIZER switch to
when you are
taking pictures using the Bulb setting (long
exposures). If the STABILIZER switch is set to
the image stabilizer function may introduce errors.
• The Image Stabilizer might not be fully effective
in the following cases:
• You shoot while riding on a bumpy road.
• You move the camera dramatically for a
panning shot in Mode 1.
• You shoot using techniques other than
following shots in Mode 2.
,
• If yu set the camera’s Custom Function to
change the assigned button to operate the AF,
the Image Stabilizer will operate when you press
the newly assigned AF button.
• The Image Stabilizer consumes more pwer
than normal shooting, so fewer shots cn be
taken if you use the function.
•
The image stabilizer operates for about two
seconds even when your finger is off the shutter
button. Do not remove the lens while the stabilizer
is in operation. This will cause a malfunction
• With the EOS-1V/HS, 3, ELAN 7E/ELAN
.
7/30/33, ELAN 7NE/ELAN 7N/30V/33V, ELAN
II/ELAN IIE/50/50E, REBEL 2000/300, IX, and
D30, the Image Stabilizer will not work during
self-timer operation.
ENG-9
8. Infinity Compensation Mark
9. Infrared Index
Distance index
Infinity compensation mark
To compensate for shifting of the infinity focus
point that results from changes in temperature.
The infared index corrects the focus setting
when uing monochrome infrared film. Focus on
The infinity position at normal temperature is the subject manually, then adjust the distance
point at which the vertical line of the L mark i
aligned with the distance indicator on the
distance scale.
stting by moving the focusing ring to the
corresponding infrared index mark.
Some EOS cameras cannot use infrared film. See
the instructions for your EOS camera.
For accurate manual focusing on subjects at
infinity distance, look through the viewfinder while
rotating the focusing ring.
• The infrared index position is based on a
wavelength of 800 nm.
•
The compensation amount differs depending on
the focal length. Use the indicated focal length as
a guide when setting the compensation amount.
• Be sure to observe the manufacturer’s
instructions when using infrared film.
• Use a red filter when you take the picture.
ENG-10
10. Filters
(Sold separately)
11. Extension Tubes
(Sold separately)
You can attach filters to the filter mounting thread You can attach Extension Tube EF12 II or EF25
on the front of the lens.
II for magnified shots. The shooting distance and
magnification are shown below.
• If you need a polarizing filter, use the Canon
Circular Polarizing Filter (58mm).
• To adjust the polarizing filter, first remove the
lens hood.
Camera-to-Subject
Magnification
Distance (mm)
Near
478
Far
616
Near
0.23×
0.26×
0.46×
0.35×
Far
70mm
0.17×
0.04×
0.38×
0.09×
EF12 ll
5 ll
300mm 1170
70mm 354
300mm 1024
7626
398
3890
Manual focusing is recommended for accurate
focusing.
ENG-11
12. Close-up Lenses
(Sold separately)
Attaching a 250D or 500D (58mm) Close-up
Lens enables close-up photography.
Compatibility with Close-up Lenses is as follows.
• Close-up Lens 250D:
Can be used at the 70mm end (magnification
0.29x - 1.18x)
• Close-up Lens 500D:
Can be used (magnification 0.14x - 0.65x)
Manual focusing is recommended for accurate
focusing.
ENG-12
Specifications
Focal Length & Max. Aperture
Lens Construction
Min. Aperture
70 – 300 mm, f/4.5 – 5.6
18 elements in 12 groups
f/32 – 40*
Angle of View
Diagonal: 34° – 8°15’
1.4 m / 4.6 ft.
Vertical: 19°30’ – 4°35’
Horizontal: 29° – 6°50’
Min. Focusing Distance
Max. Magnification & Field of view 0.19 × (at 300 mm), 432 × 650 – 123 × 183 mm / 16.8 × 25.4 – 4.8 × 7.1 inch (at 1.4 m)
Filter Diameter
Max. Diameter & Length
Weight
58 mm
82.4 × 99.9 mm / 3.2 × 39 ch
720 g / 25.2 oz
ET-65B
Lens Hood
Lens Cap
E-58/E-58 I
LP116
Case
* This figure is for models that display apertures by 1/3 increment. For models that display apertures by 1/2
increment, it is f/32-38.
• The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm to include the
E-58U lens cap and dust cap, and 24.2 mm for the E-58 II.
• The size and weight listed are for the lens only, except as indicated.
• The EF1.4X II/EF2X II extenders cannot be used with this lens.
• Aperture settings are specified on the camera. The camera automatically compensates for variations in the
aperture setting when the camera is zoomed in or out.
• All data listed is measured according to Canon standards.
• Product specifications and appearance are subject to change without notice.
ENG-13
0812Ni © CANON INC. 2004
CT1-8514-004
|
Belkin Home Theater System AP41300fc12 BLK User Manual
Belkin Network Cables PM01141ea User Manual
Black Box Network Hardware ACS4002A R2 User Manual
Blomberg Washer WNF 7201 WE20 User Manual
Bogen Speaker OCS1 User Manual
Bosch Appliances Dishwasher SHU42L User Manual
Brother Label Maker PT 65 User Manual
Campbell Hausfeld Marine Instruments PA2123 User Manual
Casio Watch MA1009 EA User Manual
Casio Weather Radio ID 13 User Manual